Don't Buy Into These "Trends" Concerning Door Lock Change > 자유게시판

How to Do a Door Lock Change

Changing your door lock is a simple and affordable way to improve the security of your home. The process is not for all. It requires a certain amount of patience and expertise.

The cylinder is contained within the knob body. The cylinder is what identifies the key when it's inserted into the lock.

Take off the lock that was previously used.

The first step is to remove the old lock. It's a fairly simple process, however there are a few points to keep in mind. Make sure your new double glazing window lock repair glazed window lock replacement lock repairs (Continued) is compatible with your door. This will ensure it is securely fitted and won't leave a gap in the latch or deadbolt.

After you've removed the latch plate, look for two bolts or screws on the inside of the casing that connect the casing and halves of the lock together. Remove them with a screwdriver, then take the lock out of the door. If you have a mortise locking, there may be a set screw at the base of the handle that binds it to the spindle. Remove the doorknobs by unscrewing this screw with a screwdriver.

Take the deadbolt and latch plug from your door jamb. Then, you can install your new lock. If you're replacing a mortise you must take a measurement of the distance between your lock case and the door edge to ensure that the new lock is a good fit.

You might want to change your lock for a variety of reasons, for instance, if you suspect that someone else is holding the key or if you've got a new roommate. You can save money if you remove the lock yourself instead of hiring a professional. It is much easier than you think and can be completed in just a few moments.

Begin by removing the trim and handle from the door. Then, pull the trim off with a flat screwdriver. You should be able to twist off most of it, and in some instances the handles could come off completely. Next, search for a pinhole on the inside of the handle, and insert a straightened clip into it. This will trigger the release mechanism, allowing you to remove the handle. Then, look for a small tab that is located inside of the lock, and press it with a flat screwdriver. Once the spindle has been removed, you can remove the housing and cylinder.

The choice of a new locking system

You have many options when it comes to choosing the right lock. Take a look at various kinds of locks, and select one that fits your door's style. Take into consideration the backset which is the distance between the edge and the center of the hole for the lock. Also consider the cross bore, a small hole in the middle of your door's frame. Choose a lock that fits the door thickness and swing.

The majority of door locks have been evaluated by BHMA and the American National Standards Institute to provide you with an idea of how well they are able to withstand the rigors of use and how difficult to disable or pick. A grade 3 lock may be ideal for a quiet urban apartment complex, whereas an entry grade lock could be more able to withstand the traffic that is frequented by a storefront on a busy city street.

Most smart door locks require a digital key code to open. If you are worried about hacking, or any other security issues, talk to an expert locksmith.

Replace the cylinder

It is easy to replace damaged or broken window lock repair door lock cylinder using a simple DIY project. The trick is to select the right cylinder, and follow the steps that come with it. The first step is to take off the knob or handle, in the event that one is present and then remove the trim that is attached to the base of the lock cylinder using the help of a screwdriver. Once the trim has been removed, you can access the screws that hold the cylinder in place and remove them with the flat-head screwdriver. The cylinder is then gently pulled out of the door.

Be sure to take measurements of the length of the new cylinder before installing it. Measure the distance from the center to the right and left sides of the cylinder with an instrument. Purchase a new cylinder which has the same measurements. This will prevent cylinders from snapping when the door is kicked or the key becomes stuck inside.

If you have a replacement cylinder, put it into the door and turn the key. This will align the cylinder with the carrier which is located usually on the outside of the lock. You can then loosen the set screws which should be a couple of turns in the head. If there is a screw located on the exterior of the case that is holding the door, you will need to remove it.

You can replace the old lock cylinder with the new one by sliding it into the case, and tightening the set screws. The process of reinstalling the component that connects the cylinder to the stem of a lock indicator is also important. You can do this by pulling three tabs in the back of the cylindrical with needle-nosed pliers. Attach the bracket that is smaller to the cylinder's back. Then, you must install the strike plate and latch plate, as well as the retaining ring that is attached to the top lock cylinder.

Installing a new lock

Start by measuring the width of your door if you are replacing a lock that is already in use. Most locksets for residential use come with a thickness of 3/8 to 1 3/4 inches. If your door is thicker it will require an extra-thick door kit that includes longer screws, a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

Most locks come with detailed instruction manual to guide you through the installation of the new hardware. Before beginning, you must read the instructions to ensure that you've followed the steps. The manual will also provide you with an idea of the level of expertise required to complete the task. You might want to ask a person who has had experience in changing locks for assistance if are changing a lock the first time.

Before installing the new lock it is an excellent idea to put cover the holes with tape the old hardware. This will prevent the screws from slipping through the holes and will also protect any tiles you might have put in. It will also prevent any potential damage from rust dirt, and grime. SECURAM Touch comes with the masking strip or gaffer tape. However, you can make use of any tape you have.

After removing the screws that hold the lock's interior to the exterior and remove the lock immediately. It's crucial to do this swiftly to avoid the lock from closing itself in a way that could end up damage the mechanism.

If your new lock has an internal latch bolt, insert the new bolt into its upper cross bore. Be sure to put it in the correct place that is usually marked by an arrow on the faceplate. Then, screw the latch plate onto the bolt.

Finally, screw the deadbolt and strike plate into the door jamb. Test the deadbolt by throwing it few times to verify that it extends all way through the strike plate and is completely secure. If you're using an electronic smart lock, make sure to follow the instructions for programming it. This involves downloading an app and registering your e-mail address, verifying your identity and connecting to the wireless network in order to connect your device.